Engine Maintenance

How Much Oil Is Your Lycoming Allowed to Burn?

Back to Blog List

Lycoming publishes an actual number for this, and it is far higher than most owners expect. The Lycoming maximum oil consumption limit comes from a formula in Service Instruction No. 1427C, and it allows a 180-horsepower engine to burn roughly a quart every hour and three quarters before anyone can call it a problem.

That surprises people. Most healthy engines use a fraction of that. The formula is a ceiling, not a goal — think of it as the speed limit sign, not the speed your car is comfortable at. What actually matters to your wallet is where your engine sits today compared with where it sat two hundred hours ago.

What is Lycoming's maximum oil consumption formula?

Lycoming states the maximum allowable oil consumption as 0.006 pounds of oil per brake horsepower per hour, and converts it to quarts per hour with this arithmetic: maximum oil consumption (qt/hr) = (0.006 × rated BHP × 4) ÷ 7.4.

The pieces are simple once you break them apart. The 0.006 is the allowance per horsepower per hour. Rated BHP is the horsepower your engine model is certificated at, not the power you happen to be pulling in cruise. The 4 converts gallons to quarts, and 7.4 is the approximate weight in pounds of a gallon of aviation engine oil.

Lycoming publishes this in Service Instruction No. 1427C, the same document that covers engine break-in. That pairing is deliberate: the company expects oil consumption to be high and unsettled during break-in, then to drop and stabilize once the rings seat. The formula is what the engine must meet after that, for the rest of its life.

One shortcut if you do not want to do the whole calculation: multiply rated horsepower by 0.00324. That gives you quarts per hour directly.

How much oil is my specific engine allowed to burn?

Run your rated horsepower through the formula and you get a number between roughly a third of a quart and a little over a quart per hour for the common Lycoming range. The table below does the math for horsepower ratings found across the fleet.

Rated horsepowerTypical Lycoming familyMaximum allowable (qt/hr)Roughly one quart every
115–118 hpO-2350.382.6 hours
150 hpO-320-E series0.492.1 hours
160 hpO-320-D, IO-360-L2A (derated)0.521.9 hours
180 hpO-360, IO-3600.581.7 hours
200 hpIO-360-A series0.651.5 hours
210 hpIO-3900.681.5 hours
235 hpO-540-J0.761.3 hours
260 hpIO-540-D, O-540-E0.841.2 hours
300 hpIO-540-K0.971.0 hour
350 hpTIO-540-AE1.140.9 hour

Look at the bottom of that table for a moment. A 350-horsepower turbocharged Lycoming is allowed, on paper, to consume more than a quart an hour and still be within limits. An eight-quart sump would not get you far. In practice a turbo engine in that condition would be grounded by its owner long before Lycoming's limit was reached, because nobody wants to carry that much spare oil.

Heads Up: Use the horsepower on your engine data plate and in the aircraft's type certificate data sheet, not the family average. The IO-360-L2A is rated 160 hp in the Cessna 172R and 180 hp in the 172S — same engine designation, different certificated output, different allowable consumption.

Flying411 keeps Lycoming-powered singles and twins in one place, so you can compare engine model, time since overhaul and maintenance history before you ever call a seller.

How much oil does a healthy Lycoming actually use?

Far less than the limit. A sound four-cylinder Lycoming with good cylinders typically runs somewhere between one quart every eight hours and one quart every fifteen hours, and plenty of well-kept engines do better than that.

Six-cylinder engines generally use a bit more, simply because there are more cylinders, more ring packs and more valve guides contributing. Turbocharged engines use more again, because turbocharger bearing seals pass a small amount of oil by design and because the engines run hotter.

The practical takeaway is that the formula almost never flags a problem before you notice one yourself. If your O-360 goes from a quart every twelve hours to a quart every four, you have a developing issue worth investigating — even though a quart every four hours is still comfortably inside Lycoming's 1.7-hour ceiling. The limit is the airworthiness floor. Your own baseline is the diagnostic tool.

Why It Matters: Insurance claims, pre-buy disputes and shop arguments get settled against the published formula, not against what feels normal. If a seller tells you the engine is "a little thirsty" at a quart every three hours, that engine is technically within limits and you will have a hard time calling it unairworthy. Price the risk instead of arguing the rule.

How do I measure oil consumption the right way?

Fill to the same mark every time, log the quarts you add, and divide by the hours flown between oil changes. Anything less disciplined gives you noise instead of data.

A clean method looks like this. At each oil change, fill the sump to a consistent level and write it down along with the tach or Hobbs reading. Every time you add oil, write down how much and at what reading. At the next change, add up the quarts, subtract the starting and ending reading, and you have quarts per hour for that interval. Do it for three or four intervals and you have a trend line.

Two details ruin the numbers for people. The first is checking oil at different times — a hot engine straight off a flight will read lower than one that has sat overnight, because oil is still draining back. Pick one habit and stick to it. The second is overfilling. Most four-cylinder Lycomings with an eight-quart sump will push the top quart or two straight out the breather within the first half hour of flight. Fill a 172 to eight quarts and you have not added oil to the engine, you have added oil to the belly. Owners of these engines generally settle on six quarts for local flying and seven for longer legs, and their measured consumption improves overnight.

Lycoming's guidance on oil change intervals sits in Service Bulletin No. 480F and Service Instruction No. 1014: 50 hours for engines with a full-flow filter, 25 hours for those with a pressure screen only, and in either case not longer than four calendar months. Those intervals are also your natural measuring windows.

Is my engine burning oil or leaking it?

Oil leaving the engine as a liquid leaves evidence; oil leaving as smoke usually does not. Before you condemn a cylinder, find out which one you have.

Leaks are the cheaper answer and the more common one. Look for wetness and streaking at the pushrod tube seals, the rocker box gaskets, the accessory case parting line, the prop governor pad, the crankcase through-bolts and the front crankshaft seal. A dirty belly with a wet, oily film that collects dust is the classic signature. So is oil tracking back from the breather tube, which points at crankcase pressure rather than a gasket — and crankcase pressure points back at blow-by past the rings.

Burned oil shows up differently. You may see a faint blue haze on start-up or on descent after a long cruise at low power. Spark plugs come out with oily, wet deposits rather than dry grey ones, and if it is one cylinder, it will usually be the same plug every time. The exhaust stack on that cylinder may be sootier and oilier than its neighbours.

A borescope settles most of these arguments in twenty minutes. Glazed cylinder walls, worn or carboned ring lands, scored barrels and worn valve guides are all visible, and a good shop will photograph what it finds.Pair that with a differential compression check performed per Lycoming Service Instruction No. 1191A, which specifies a 0.040-inch orifice tester and treats cylinders reading 70 psi or higher, within about 5 psi of each other, as satisfactory.

Where the oil goes when it is burned

Three paths cover nearly all of it. Past the piston rings into the combustion chamber, which is wear or glazing. Down the valve guides, which is clearance wear and shows up most in engines that sit. Or out the breather as mist, carried by blow-by gases that worn rings are pumping into the crankcase. The third one fools people into thinking they have a leak, because the oil really does land on the belly.

Why would oil consumption suddenly go up?

A sudden jump almost always has a mechanical cause, and the three usual suspects are a broken or stuck ring, a worn valve guide, and cylinder wall glazing from too much low-power operation.

Glazing is the one owners inflict on themselves. An engine babied at low power during break-in, or flown only in short bursts around the pattern, can polish its cylinder walls so smooth that the rings never seat. Consumption climbs and stays climbed until the cylinders are honed and the rings re-seated. Lycoming's break-in guidance in SI 1427C exists precisely to prevent this: run the engine hard, at 65 to 75 percent power, and keep it there until consumption settles.

Corrosion is the other owner-inflicted cause, and it hits aircraft that fly a few hours a month. Rust on cylinder walls acts like sandpaper on the rings. That same pattern of disuse is what destroys camshafts and lifters, which is why low-use engines need a deliberate corrosion strategy rather than hope. If the airplane is going to sit for months, pickling the engine properly costs less than a cylinder.

Then there is the boring explanation. Switching oil grades, flying in much hotter weather, or running a different power setting will all shift consumption somewhat. So will a change of oil type — if you moved from straight mineral oil to an ashless dispersant blend, or the other way, expect the number to move. The difference between those two is covered in our guide to Lycoming mineral versus ashless dispersant oil, and it matters more than most owners think.

Finally, check the simple things before the expensive ones: a cracked or partially blocked breather line, a dipstick not seated, an oil cooler hose weeping, or a filler cap left loose. More than one "high oil consumption" squawk has been fixed with a new cap gasket.

How much oil should a newly overhauled engine use?

More than a seasoned one, and that is normal for the first 25 to 50 hours. Lycoming expects consumption during break-in to be elevated and erratic, then to drop and level off once the rings seat against fresh cylinder walls.

Fly it hard. The single most common way to ruin a new top end is to cruise at 55 percent power to "be gentle," which produces exactly the low cylinder pressures that leave rings unseated. Use the break-in oil Lycoming specifies in Service Instruction No. 1014, which is mineral oil for most non-turbocharged engines and ashless dispersant oil for turbocharged engines, keep the first flights long enough to get everything up to temperature, and avoid long descents at idle.

Once consumption settles, write that number down. It becomes the baseline you will compare against for the next two thousand hours. An engine that stabilizes at a quart every ten hours at 60 hours and is still at a quart every ten hours at 900 hours is telling you something very reassuring.

Flying411 lists aircraft with engine times, overhaul dates and shop paperwork in one place, so you can compare a freshly overhauled airframe against a mid-time one without chasing six different sellers for logbook pages.

Does rising oil consumption mean I need an overhaul?

Not by itself. Oil consumption is one of four or five signals, and a decision made on any single one of them is usually a decision made too early or too late.

The signals worth reading together are differential compression readings, what the borescope shows inside each cylinder, what comes out in the oil filter, what oil analysis trends say about wear metals, and whether the engine still makes rated power and static RPM. Rising oil use with clean compressions, a clean filter and good borescope images often points at valve guides or one tired cylinder — a top-end job, not a teardown. Rising oil use alongside falling compressions across several cylinders, steel in the filter and climbing iron in the oil report is a different conversation entirely.

The filter is the loudest of those voices. A few fine fuzzy particles are routine; shiny flakes, chunks or a measurable quantity of ferrous material are not. Our guide to metal in the oil filter and Lycoming's published limits covers what each type of debris usually means.

It is also worth remembering that TBO is not a legal limit under Part 91 for most owners. Condition drives the decision. An engine 300 hours past published TBO with stable consumption, strong compressions and a clean filter can be a better engine than one at 1,200 hours that has been climbing a quart every hundred hours for two years. If you do reach the decision point, our breakdowns of Lycoming overhaul cost and downtime, overhaul versus replacement, and why two shops quote thousands apart will keep the numbers honest.

Pro Tip: Plot consumption rather than listing it. Quarts per hour on the vertical axis, engine hours on the horizontal. A flat line with scatter is a healthy engine. A line that bends upward over two or three oil changes is the thing to act on, regardless of where it sits relative to Lycoming's ceiling.

What does high oil consumption do at a pre-buy or resale?

It knocks money off the price, and the amount is usually tied to whichever repair the buyer's mechanic thinks is coming. A single tired cylinder is a few thousand dollars. A top overhaul on a six-cylinder is a great deal more. A full overhaul resets the conversation entirely.

If you are buying, ask for the oil addition records, not just the oil change entries. Sellers who log every quart are telling you something about how the airplane has been maintained. If no records exist, a careful pre-buy should include a borescope of every cylinder and a compression check done to SI 1191A — and you should treat an unknown consumption rate as a risk you are pricing, not a detail you will sort out later.

If you are selling, the fix is boring and effective: establish a measured consumption figure over at least two oil change intervals, put it in writing, and attach the borescope images. A documented quart every eleven hours removes an entire category of buyer anxiety. Vague reassurance does the opposite. The same logic applies to any open Lycoming squawk — documented and quantified beats undefined every time.

Flying411 gathers Lycoming-powered listings with their engine details in one place, so you can compare asking price against time since overhaul and known engine condition rather than guessing.

At a Glance

The Lycoming maximum oil consumption limit comes from Service Instruction No. 1427C and works out to 0.006 pounds per rated horsepower per hour, or roughly 0.00324 quarts per hour per horsepower — about 0.58 qt/hr for a 180-hp engine and close to a full quart per hour for a 300-hp six. That is a ceiling for airworthiness, not a target, and most healthy engines use a quart every eight to fifteen hours. Measure your own rate by filling to a consistent mark and logging every quart added between oil changes, and be careful not to overfill, because the top quart or two usually goes out the breather. Rule out leaks and breather mist before suspecting rings, use a borescope and a compression check to SI 1191A to find the cause, and read rising consumption alongside filter debris, oil analysis trends and compression rather than on its own. A new or overhauled engine should settle within 25 to 50 hours if you fly it at 65 to 75 percent power during break-in — and the number it settles at is the baseline worth guarding for the rest of its life.

When you are ready to compare listings, visitFlying411and see what is on the market today.